Bendpak 35,000 lb 4 post lift
Specializing in car & truck lifts, brake lathes, pipe benders, tire changers, and wheel balancers, and much more! ARESCO, Inc. is the
source for all of your automotive equipment needs. We carry a full line of equipment and replacement parts for most makes and models.
With over 25 years of experience in the automotive industry, we at ARESCO are committed to providing our customers with quality
products and service.
1-877-2ARESCO
Automotive Repair Equipment Supply COmpany
or 1-877-227-3726
792 N Perry St Pontiac MI 48342
DP-30
(5150509)
WSA-100
(5210436)
RJ-15
(5175348)
RJ-18
(5175470)
RJ-25
(5175469)
HDS-35X 35,000-lb. Capacity
Extended-Length Four-Post
Truck Lift
BendPak's HDS-Truck Series four-post lifts are a whole new
breed of rugged. They're newly engineered super-duty truck
lifts that make light work out of heavy lifting. They work better,
are built to last, and feature upgrades that increase safety,
durability and productivity. Four models provide a generous
35,000 or 40,000-lb. lifting capacity and feature extra-wide
runways to accommodate a wide variety of vehicle
configurations.
Looking for even more lifting capabilities? Check out the
40,000-lb. capacity HDS-40 or the extended 40,000-lb. capacity
HDS-40X.
All HDS-35X extended length truck lifts feature:
Spring-loaded safety locks automatically engage continuously
during rise and adjustable safety ladders allow for precise
runway leveling even when installed on sloped floors.
Supersized 12” diameter cable sheaves within the runway and
cross tubes combined with massive 4” diameter sheave axles
dramatically improve cable wear and critical component
lifespan meaning you’ll increase safety and spend less money in
service related expenses down the road.
BendPak's HDS-Truck Series lifts feature four stainless-steel
lifting cables that provide a great balance between abrasion
resistance and fatigue.
Grease nipples are located on every sheave and sheave axle to
make lubrication maintenance a breeze.
Each HDS-Truck Series four-post lift is equipped with a single
hydraulic cylinder hidden away under the runway for maximum
performance and reliability and minimum exposure to elements.
The hydraulic cylinder features high-durometer rod seals,
pressure loaded U-cup piston seals, backups and wear bands
that virtually eliminate any fluid bypass. The welded cylinder
body is made from high strength steel tubing produced to
exceed ASTM specifications. This combination of superb base
material and superior processing ensures straight, smooth,
cylinders that will provide years and years of dependable
trouble-free service.Leak proof cylinder technology only
available for BendPak four-post lifts
An integrated hydraulic flow restrictor provides a controlled
descent in the unlikely event of an unexpected hose rupture.
A durable powder coat finish can withstand harsh environments
and chemical spills and will provide years of protection.
A simple push-button pneumatic lock release makes lowering
operations simple and fast. Aircraft-quality stainless steel and
aluminum pneumatic cylinders will provide years of trouble-free
service.
A secondary lock system is on constant guard and acts as a
slack-cable device in the unlikely event of an unexpected cable
failure.
Lifting cables, airlines, safety latches and sheaves are all fully
enclosed within lift structure.
Features multiple adjustable height locking positions for
variable-height parking and infinite leveling.
A maintenance-free electric hydraulic power system assures
ultimate dependability.
All operator controls are conveniently located within easy
reach.
12" x 12" base plates provide a solid foundation.
Non-skid runways provides maximum grip, even when the
runway surface is wet or oily.
Optional rolling jacks make a great addition to increase service
capacity. Rolling jacks are used to raise the front or rear
portion of a vehicle off the runways allowing operators to
perform efficient wheel and break service. A pair of jacks
allows the entire vehicle to elevated. Each jack has telescoping
arms and frame contact pads that can be extended over the
runways and positioned under vehicle lifting points. Each jack
features three safety-lock positions and stackable truck and
van adapters for increased lifting height and better access to
frame contact points on high ground-clearance vehicles. The
jacks come equipped with a commercial grade air-hydraulic
pump.
*Not all BendPak lift models meet the standards as prescribed
by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list or contact BendPak via
contact@bendpak.com.
Features & Specifications
35,000-lb. lifting capacity
CE Approved and Certified. Meets or exceeds the standards
prescribed by European Standard EN 1493
Extended length runways
Supersized 12" diameter cable sheaves
Stainless steal lifting cables
Grease nipples
Single hydraulic under-runway cylinder
Integrated flow restrictor
Durable powder coat
Spring-loaded safety locks
Second lock system on constant guard
Fully enclosed lifting cables
Multiple adjustable height locking positions
Maintenance-free electric hydraulic power system
Conveniently positioned operator controls
12" x 12" base plates
Non-skid runways
Optional rolling jacks
Specifications
Lifting capacity*: 35,000 lbs. / 12,247 kg
*Max capacity / front axle: 17,500 lbs. / 7,938 kg
*Max capacity / rear axle: 17,500 lbs. / 7,938 kg
Overall width: 154" / 3,912 mm
Outside length: 317" / 8,052 mm
Overall length: 357" / 9,068 mm
Height of columns: 93" / 2,362 mm
Runway min height: 8-1/2" / 216 mm
Max rise: 60" / 1,524 mm
Max lifting height: 68-1/2" / 1,740 mm
Width between posts: 134" / 3,404 mm
Runway width: 28" / 711 mm
Width between runways: 36" – 47" / 914 mm – 1,194 mm
Runway centerline: 64" - 75" / 1,625 mm to 1,905 mm
Outside edge of runways: 92" - 103" / 2,367 mm - 2,616 mm
Drive-thru clearance: 109" / 2,769 mm
Length of runways: 323" / 5,842 mm
Min wheelbase @ rated capacity: 230" / 5,842 mm
Min wheelbase @ 75% capacity: 195" / 4,953 mm
Min wheelbase @ 50% capacity: 165" / 4,191 mm
Min wheelbase @ 25% capacity: 130" / 3,302 mm
Locking positions: 9
Lock spacing: every 6" / 152 mm
Lifting time: 75 sec
Motor: 220 VAC / 60 Hz / 1 Ph
Note: An air supply (minimum: 30 psi / 3 CFM) is required for the
safety-lock mechanisms to disengage. It is solely the
responsibility of the end-user to provide, install and maintain the
air supply.
*Not all BendPak lift models meet the standards as prescribed
by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list or contact BendPak via
contact@bendpak.com.
Copyright©2014 www.aresco.org all rights reserved web design by M.Miller